As described at the end of Part 1, I wasn’t satisfied with the U-shaped weatherstrip, so I took the patio door back off the hinges and cut two groves (or channels) in the new door bottom to attached the original style kerf-mounted weatherstrip – a Frost King UDS36 model that I purchased at Home Depot.

The Rotozip® Spiral Saw™ with a Jigsaw Handle Kit and Straight Edge Guide made the job easy.  After duct tape and my Dewalt cordless drill, the Rotozip is my 3rd favorite tool.

Cutting Groves in the Door Bottom for the Weatherstrip

U-Shaped Door Bottom Weatherstrip

I removed the French door and set it back in the door jigs in my workshop. Notice the dark spots on the concrete floor from water dripping from the inside the door sweep. If you decided to install a U-shaped doorsweep, be sure to caulk the top seam and screw heads to prevent water from seeping inside. Note the Frost King instructions state the screws go on the exterior side of the door, exposed to the weather.

French Door with Frost King U-Shaped Weatherstrip

Removing the weatherstrip was simple, just remove the screws and slide off the weatherstrip.

Cutting Grooves in the Door Bottom for the New Weatherstrip

I bought a RotoZip Jigsaw Handle Kit that includes a Straight Edge Guide from Amazon.com after finding that none of the hardware stores in my area stocked this specialty item. The ability to use the Rotozip as a router to cut the door bottom groves made this an obvious choice. If you have a router and straight edge attachment, that would also work fine. The jigsaw handle kit comes with everything you see here.

Rotozip Jigsaw Handle Kit

Two straight pieces of scrap 2×4 boards were fastened together with wood screws and clamped to the bottom of the patio door to provide a wide base and edge for the straight edge guide.

2x4s Clamped to Door for the Jigsaw Straight Edge Guide

To illustrate the task at hand, a section of new kerf-mount weatherstrip is held against the door bottom to illustrate the two slots (red lines) to be cut in the door bottom with the Rotozip for the spines. The Frost King UDS36 weatherstrip is 36 inches long and my door is 32 inches wide, so I had some spare material to work with here.

Weatherstrip Section and Grooves to be Cut in Door Bottom

Two blue lines are marked with a straight edge for the cuts. The red highlights are added for clarity in this photo. The lines – and corresponding cuts to be made – stopped 1 inch from the ends of the bottom frame.

Door Bottom Grooves Marked for Weatherstrip

Choosing the right size Rotozip bit took a bit of thoughtful consideration. The bits are compared to the spines on the weatherstrip. The 5/32 inch bit would seem to be the correct size, but in reality it cuts a channel (leaves a kerf) that is too large because the bit tears away a slightly larger amount of wood than the diameter of the bit. The right choice is the 1/8 inch bit on the left. I made test cuts on scrap wood to decide which bit is best.

Rotozip Bits and Door Weatherstrip

The jigsaw handle was adjusted such that the depth of the bit – and the corresponding groove was about 1/8 inch deeper than the spine of the weatherstrip. However, the Rotozip bit was too long for the maximum height adjustment of the jigsaw handle and would have resulted in a cut that was far too deep. I therefore used a Dremel Tool and cutoff wheel to shorten the unfluted end of the bit by about 1/2 inch. This allowed me to make the shallow cut needed for the spines without slicing through the 3/4 inch thick wood frame.

To make the cuts:

1. Put on your safety glasses.
2. Make sure the Rotozip is turned off.
3. Set the tip of the drill be on the line to be cut.
4. Tip the saw forward (up in my case) such that the straight edge guide catches the outer 2×4.
5. Adjust the depth of the edge guide and tighten the lock screw.
6. Recheck the alignment.
7. Turn on the Rotozip.
8. Hold the straight edge guide firmly against the 2×4.
9. Lower the bit into the wood on the marked line.
10. Move the saw at a steady pace while holding the fence firmly against the 2×4.
11. At the end of your cut, rock the saw downward to raise the bit out of the kerf (i.e. groove).
12. Turn off the saw. Redo from Step 3 for the other groove.

Cutting Groves in the Door Bottom for the Weatherstrip

I found the Rotozip left a lot of sawdust in the kerf (a.k.a. groove or slot) that had to be knocked loose with the tip of a screwdriver and vacuumed out. This may have been caused by the relatively moist pressure treated wood.

Installation of the new kerf-mounted weatherstrip from this point is identical to this How To article. However, I changed my mind here on the orientation of the weatherstrip and placed the tube-side (right side in the photo below) on the exterior side of the door because I had slightly more clearance on the basement patio door, so this seemed to make for a better seal. The Frost King instructions don’t indicate which way it should go and the original weatherstrip had tubular sections on both sides of the weatherstrip with straight fins in the middle.

Kerf Mounted Door Bottom Weatherstrip - Frost King UDS36

The final step was to drill two pilot holes in the bottom of the vertical door frames and fasten ends of the weatherstrip with 1 inch pan-head corrosion-resistant wood screws. I put a small dab of exterior caulk in the pilot holes first to seal around the woods screws.

In Retrospect

At the time, the U-shaped weatherstrip seemed like a good idea but I wasn’t satisfied with the result. If I were to do this project over again starting back at Part 1, I would have used a table saw to cut two full length slots for the original kerf-mount weatherstrip.  Unfortunately, a Delta 10″ Unisaw table saw isn’t in my workshop. But you can always contact a friend who has a table saw or stop by a cabinet shop and ask them to make the cuts for you.

Hope this helps,

Bob Jackson

Bookmark It!