Home » House Interior » Bathroom » How to Fix a Sewer Gas Smell

How to Fix a Sewer Gas Smell

Bob Jackson
Last Updated on
by Bob Jackson

This project explains how to fix a sewer gas smell coming from under the bathroom sink by replacing the one-way air admittance plumbing valve.

A distinct sewer gas odor was coming from the bathroom sink area. At first I wondered if there were a leaky pipe or such. Sniffing around, it was clearly strongest under the vanity. I discovered the Studor® Mini Vent, a plumbing air admittance valve had gone bad, allowing sewer gases to back flow into the house.

Studor Mini Vent under Bathroom Sink
Studor Mini Vent under Bathroom Sink

How to Fix a Sewer Gas Smell

Studor Mini Vent

The Studor Vent is a one-way air admittance valve that allows air to flow into the drain pipe but not out into the room. Running water going down the drain pipe creates a vacuum that could siphon the U-trap dry. The purpose of the U-trap (also called a P-trap or J-trap) is to create a water seal to prevent sewer gasses from coming back up the sink drain. The Studor Vent allows air into the pipe to break the vacuum preserving the water seal in the U-trap.

The Studor vent is commonly installed under the sink at least 4″ inches above the weir of the trap in situations where connecting to a vent pipe to the roof is not practical. A quick inventory of my house found a Studor Mini Vent is installed at nearly every bathroom sink and the kitchen sink.

Studor Mini Vent Air Admittance Valve
Studor Mini Vent Air Admittance Valve

Plumbing Air Vent Malfunction

This vent is about 8 years old and malfunctioned because flies and mosquitoes (yuck!) from the sewer line had clogged up the valve, preventing it from fully closing to seal out the sewer gases.

Studor Mini Vent Clogged with Insects
Studor Mini Vent Clogged with Insects

Install the New Sewer Vent

A new Studor Mini Vent was purchased at the local home improvement for about $23.00. The old vent was removed with a pair of Channel Lock Pliers because the threads were tight due to the hardened plumbers putty on the pipe threads. Aside: Do not use Plumber’s Putty on the Studor Vent threads! The plumber made a mistake when the original vent was installed. Be sure grasp the main pipe firmly to minimize torquing the PVC glue joints when unscrewing the old vent.

The threads of the new Studor Vent are wrapped with a two or three turns of PFTE thread seal tape or Teflon Thread Seal Tape (if using the Du Pont name brand tape as I am), then new vent screwed on hand tight:

Studor Mini-Vent Installation
Studor Mini-Vent Installation

Replacing the Studor Mini-Vent only required 5 minutes or so to do the job.

Fix a Sewer Gas Smell: Studor Mini-Vent Replacement
Fix a Sewer Gas Smell: Studor Mini-Vent Replacement

Studor Mini Vent installation instructions are available on the manufacturer’s web site here (see page 15).

Additional Studor Mini Vent installation photos are available here about 1/2 down the page.

Faucet Connectors

While I was working on the sink, I also replaced the original cheap gray plastic hot & cold water faucet hook-up lines with heavy-duty vinyl faucet connectors reinforced with a braided stainless steel wire. I worried those cheap gray lines might burst and flood the house some day. An easy job, just turn off the faucet water supply valves inside the sink cabinet and the rest is working with two adjustable wrenches.

Hope this saves you some money.

Bob Jackson

air admittance valveair valve for drain pipebathroom sinkfix a sewer gas smellhow to fix a sewer gas smell
Bob Jackson
Bob Jackson
Technology product manager by day and a prolific handyman in the evenings and over the weekends. Bob was the founder of the original Handyman How To website and that tradition continues on this site with excellent new handyman content into the future.
Leave a Reply

Your email address will not be published. Required fields are marked *